The Brawler MID front bumper for JK is a "mid-width", high clearance bumper designed to combine off-road performance with full features. This bumper is fabricated from 3/16" plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend farther outboard than our Brawler Lite bumper, to about half the width of the tires. This provides increased brush protection for the grille corners and fenders, and gives the Jeep a more "expeditionary" look than our more rock-crawling specific bumpers. This product ships as bare steel—it will need to be painted or powder coated prior to final installation.
This bumper is fabricated from 3/16" plate steel, CNC laser-cut and precision brake-formed into a low profile, high clearance design. The ends of the bumper extend far enough to protect the lower corner of the JK grille, but not far enough to hinder tire clearance or tire access to vertical obstacles.
The Brawler Bar is modeled after the bar found on our original RockBrawler front bumper. It is a low-profile stinger designed to provide protection to the winch, grille and radiator area. The Brawler Bar is made of CNC laser-notched, NC-bent 1¾" diameter .120" wall DOM tubing. The complex laser-cut notch allows the Brawler Bar to be welded to two different planes on the surface of the bumper, providing incredible strength. Two gusset styles are offered for strengthening the Brawler Bar. CNC laser-cut brake-formed 3/16" plate steel or CNC laser notched DOM tubing. Note: Warn PowerPlant winches are not a direct-fit with the DOM Tube gussets (they may be installed with some minor modifications by the installer).
The Brawler MID can be mounted without cutting or altering the Jeep's frame rails. The faceted design of the Brawler MID provides the best ground clearance and approach angle possible in a bumper that doesn't require frame modifications. The factory "Crash Bar" may be left intact or removed for a sleek appearance and high clearance. If keeping the crash bar, we recommend adding the Brawler MID Skid Plate (sold separately), which conceals the crash bar and protects the electronic sway bar disconnect.
Brawler MID comes with provisions for re-mounting your factory fog lamps. These consist of recessed fog lamp "buckets" that are made of CNC laser cut DUM tubing with a mounting flange designed to accept the mounting hardware of the stock lamps. The recess and all-steel buckets help protect the lamps from the rocks. For those who do not have the stock fog lamps, or would like to upgrade to more powerful LED lamps, Poison Spyder offers a unique LED Fog Lamp Mounting Kit for installing a pair of Rigid Industries "Dually" LED lamps in the fog lamp locations.
IMPORTANT: The stock fog lamps used on the Jeep Wrangler 10th Anniversary Rubicon do NOT fit into the fog lamp buckets on this bumper. If installing this bumper on a 10th Anniversary Rubicon, we suggest using a pair of Rigid Industries Dually or Dually D2 LED lamps along with our JK Dually Fog Lamp Mounts instead of the stock fog lamps.
The Brawler MID bumper is designed to accept most Warn winches, and winches from other manufacturers that conform to Warn's standardized winch mounting dimensions. The winch sits in a slight depression on the top surface of the bumper, with plenty of CNC laser cut plate steel gusseting inside the bumper shell, directly underneath the winch to provide maximum strength. The Winch Fairlead Mount is sold separately, so that those who wish to not run a winch are left with a clean looking, unobstructed top surface on their bumper. IMPORTANT: installing the Warn ZEON winch on the Brawler MID Front Bumper requires TWO sets of our ZEON Winch Spacer Plates (p/n 45-57-010-03, sold separately).
Recovery Shackle Tabs are modeled after the high clearance tabs designed for our hard core BFH series bumpers. These tabs are angle to provide maximum approach angle. They are CNC machined from 1" thick steel billet, specifically designed to accept our heavy duty 3/4" Recovery Shackles.
The part number for this item is Poison Spyder 17-63-010-DBT and it fits 2007-2016 Jeep Wrangler models.
This product ships as bare steel—it will need to be painted or powder coated prior to final installation.