The Snow Performance Stage 3 Boost Cooler is the most advanced water-methanol injection system for your DI (direct injected) and forced induction (turbocharged/supercharged) vehicle. The Stage 3 Boost Cooler water-methanol injection kit creates a 2D injection map based off boost and fuel pressure sensor voltage to deliver the most accurate and tunable water-meth delivery on the market. Taking it one step further the Stage 3 will control 2 Hyper-Sonic Nozzles independently of one another to solidly the exact amount of water-methanol is provided at all rpm ranges of the engine. This 2D map injection and dual stage technology translate into the most accurate injection curve and tuneability of any water-methanol system giving 50-110 HP gains and up to 150 degree reduction in air temps! Tie this in with the industry leading Snow Performance 300 PSI UHO pump, Hypersonic Nozzles™, and the Stage 3 promises to be the easiest and most effective water-methanol system on the market for your Direct Injected / Boosted vehicle.
300 PSI UHO (Ultra High Output) Pump
3 Qt Reservoir
All Tubing Necessary for Installation
Digital Variable Mapping Controller
Power Solenoid Upgrade
Level Switch Upgrade
2 Nozzle Holder/Check Valve Combo
4 Hyper-Sonic Nozzles
Required Hardware Needed For Installation
Comprehensive Instructions to Install on any Direct Injected /Boosted Vehicle
The part number for this item is Snow Performance 320 and it fits any direct injection turbocharged or supercharged vehicle.
1. What are the benefits of Water/Methanol injection?
Boost Cooler Benefits (Gasoline):
1. Low cost - where else can you get up to 60HP for as low as $275?
2. More power than other means of detonation control.
3. Efficiency - leaner air fuel ratio can be utilized for normal operation.
4. Greatly increases air charge densities for huge horsepower increases.
5.Allows you the ability to greatly increase boost on turbos and superchargers (if you have one).
6. Increases the effective octane of your fuel as high as 115 octane. Its like running race gas!
2. If I don't have a turbo or supercharger, can the Boost Cooler be applied to naturally aspirated and or nitrous engines?
YES! 1.Naturally aspirated/high compression engines:
In this application, water/methanol injection allows the use of pump fuel in all but the most extreme situations which effects tremendous cost savings as well as horsepower increases due to air density increase and realized timing potential. The system is activated by a boost referenced switch so that injection takes place only during high engine loads when needed.
2. Engines using nitrous: With nitrous, water/methanol injection allows the use of full timing even with large (250HP+) quantities. Injection is controlled by the same means that controls nitrous injection.
3. Naturally aspirated/stock compression: With naturally aspirated engines with less than 10:1 compression, water/methanol is used typically in warm climates to get the intake temps back to 60f. Benefits include: 10-15 HP increases from air density increases and full timing, Increased gas mileage, and carbon free combustion chambers. Activation is by a throttle switch adjusted for onset engine load. With this application, the nozzle is sized so that no more than 10% of total fuel consumption at peak flywheel HP is injected.
3. Do I need an intercooler with Water/Methanol Injection?
NOT TYPICALLY - Up to approximately 30 psi boost, water/methanol injection (using at least 50% methanol) will provide all the density increase/detonation control needed in most applications. Of course, intercooling and water/methanol injection would provide even greater benefits especially beyond 30 psi boost. Most air-to-air intercoolers are only 50-65% efficient. That means for example, that with 11 psi of boost and the resulting 120degreesf air charge temperature increase, an intercooler reduces the air charge temperature only 60 degrees. Also, an intercooler will reduce boost 2 - 4 psi. on average.
4. Why not use a windshield washer pump?
Water/Methanol must be injected at above 50psi to properly atomize. Lower than 50psi causes greatly reduced air charge cooling as the result of larger droplets and their reduced total surface area. Also with inadequate atomization, there is a greater propensity to quench combustion resulting in a loss of power.
5. Why Methanol?
Methanol is a high octane fuel that is extremely resistant to detonation with an excellent cost/benefit ratio. ($1.50 - $2.00 per gallon.) Its high latent heat of vaporization also makes it an excellent air charge cooler which means a denser mixture and more horsepower. Because of these facts, it is a better anti-detonant than ethanol or iso-propanol although they will work in a pinch. It has however only about 60% of the energy content of gasoline by volume so about twice as much is used to make similar power if used as a straight fuel. It is extremely toxic and should be handled with rubber gloves in well ventilated areas only. Care should be taken to avoid skin contact.
6. Where can I purchase Methanol?
Most people simply buy windshield washer fluid from the local parts store, but Methanol can generally be purchased where racing fuels are sold. Also, most gas line dryers like "Heat" are simply Methanol. Suppliers of industrial chemicals can also supply Methanol usually at a higher price than fuel suppliers.
Most windshield washer fluids are up to 40% Methanol and 58% water. Although most contain some glycol and detergent(less than 1%), most windshield washer fluids are up to 40% methanol. Try to find one that indicates "contains methanol" and is rated to -20ºf. The bottle should state the mixture on the bottle. Name brands typically have a better mixture than off brands, but not always so be sure to look.
7. What ratio of water/methanol is recommended?
A 50/50 ratio is recommended. This has been demonstrated to be the best for charge/air cooling, excellent detonation control, and safety.
8. How long does the fluid last?
The range you'll get out of our system depends on a couple of variables:
- How much power you're making
- The settings of your system
- How aggressively you drive
In most instances our standard 2 quart reservoir works well to provide the required amount of fluid. We have seen that a 2 quart reservoir provides enough fluid for a 400-500 hp car to make 12-15 full throttle quarter mile passes.
For those looking to get more range out of their system, they can tap into their factory windshield washer reservoir and use it to hold water/methanol. This is a good option because most washer reservoirs have a large capacity (normally at least a gallon) plus they're already methanol resistant (washer fluid has methanol in it). Also, the washer reservoir is already under the hood so it doesn't require having to add another bulky item into the engine bay.